Fast-Responding Pressure Sensitive Paint
TurboFIB™ PSP
(Product ID: TF-XXX)
TurboFIB™ pressure sensitive paint (PSP) is a single-luminophore, single application PSP formulated to be applied with paint spraying equipment. TurboFIB® provides many of the advantages of UniFIB® PSP, but with faster response (1 kHz) and reduced temperature sensitivity. This paint formulation may be excited effectively from 380-nm to 550-nm, however, 400-nm radiation from ISSI LED modules is recommended for ideal response and pressure sensitivity. The paint may be applied to most surfaces, though it is recommended that plastics and rapid prototyping resins first be coated with SCR-XXX (Screen layer) or FB-XXX (FIB Basecoat™) to protect the surface from solvent damage. The calibration of TurboFIB® (shown below) is very stable and repeatable thus TurboFIB™ is recommended for advanced/professional PSP users who seek high quality data. Paint is sold in quantities of 200-ml, 400-ml. Custom quantities are available upon request. Surface coverage is approximately 1 m2 per liter.
Specifications
Pressure sensitivity | 0.8% per kPa |
Pressure range | 0-kPa to 200-kPa |
Temperature sensitivity | 0.4% per °C |
Temperature range | 0°C to 50°C |
Response time | < 1-ms |
Excitation | 380-nm to 520-nm |
Emission | 620-nm to 750-nm |
Photo-degradation rate | 1% per hour |
Shelf life | 12-months |
Filter | 610-nm |
Light Source | 400-nm |
Downloads
TurboFIB™ Painting Instructions.pdf
Calibration (PSP-CCD-M): TurboFIB™
Calibration (PCO.1600): TurboFIB™
Available quantities: 200-ml, 400-ml, 750-ml
Surface coverage is approximately 1 square meter per liter.
Calbration of TurboFIB™ PSP
Emission spectra of TurboFIB™ PSP
Excited using LM2X-DM-400 LED
TurboFIB™ Response to Nitrogen Fluidic Oscillator Impingement (Left: Intensity Response vs. Time, Right: G (dB) vs Frequency)
Porous, Fast-Response PSP
(Product ID: FP-XXX)
Porous, Fast-Response PSP is a three component, single-luminophore high speed pressure sensitive paint (PSP) formulated to provide high speed response (>10kHz) suitable for unsteady pressure measurements with high pressure sensitivity. The temperature sensitivity of these paints is higher than UniFIB® or TurboFIB™ so this PSP is best suited for isothermal environments. This paint comes in three parts. Determine how much PSP you need for your application and measure out part A by volume. Part B will be measured out 4% by volume of part A (a reusable measuring syringe is provided with the order for convenience). Shake the part A and B mixture well. This mixture is to be sprayed with paint spraying equipment on to the surface of study with a wet application to achieve a smooth finish. This application is the base layer. Once the base layer is dry, apply part C with paint spraying equipment, the overspray. The overspray, part C, may be reapplied more than once. A typical order would be a 100mL kit which would consist of three containers: 100 mL of part A, 5 mL of part B, 100mL of part C.
Specifications
Pressure sensitivity | 0.6% per kPa |
Pressure range | 0-kPa to 200-kPa |
Temperature sensitivity | 3.6% per °C |
Temperature range | 0°C to 80°C |
Response time | < 100-µs |
Excitation | 380-nm to 550-nm |
Emission | 600-nm to 720-nm |
Photo-degradation rate | 1% per minute |
Shelf life | 3-months |
Filter | 610-nm |
Downloads
Porous, Fast-Response PSP Painting Instructions.pdf
Porous, Fast-Response PSP SDS Part A.pdf
Porous, Fast-Response PSP SDS Part B.pdf
Porous, Fast-Response PSP SDS Part C.pdf
Porous, Fast-Response PSP Datasheet.pdf
Calibration (PCO.1600): Fast Porous PSP
References: Dynamic Pressure Sensitive Paint Demonstration in the AEDC Propulsion Wind Tunnel 16T
Investigation of Passive Flow Control of Cavity Acoustics Using Dynamic Pressure-Sensitive Paint
Available quantities: 100-ml, 200-ml, 400-ml, 750-ml
For the 100-ml quantity, the coverage is about 1 square foot.
Calibration of Porous Fast-Response PSP
Emission Spectra of Porous Fast-Response PSP
Excited using LM2X-DM-400 LED
Mean and unsteady pressure distribution on the 3/16-inch normal injection block operating at 703-kPa using fast porous PSP.
Porous, Fast-Response PSP framing at 25 kHz on transverse jet injecting into Mach 2.0 flow
For ordering information, please contact our sales department: issi-sales@innssi.com or call us at (937) 630-3012